Brass Door Bell Push Button Lacquered Finish Button Pack of 2

Basic doorbell, better quality than most.

As basic doorbells go, this is the most stout.

good product!

looks good easy to install !

Polish brass door bell.

Very nice front door door bell.

Quality

Excellent quality

4.0 out of 5 starsPretty Good

Bought this for my mother-in-law who wanted a brass door bell. This one does the trick but the quality could be a little better. The Finish is not quite as nice as she would like it to be.

Good

Easy to install,

It works

It works, unlike the previous two from local hardware stores. I just needed a switch, not a lighted plastic module with a printed circuit board. And which did not accept 6-12 volt ac current as traditional doorbells do. It does not push "value added" plastic on me. It promises to be long lasting, it is attractive, and it is made in India (an actual democracy that is far to be preferred to China).

Get the W-D 40 out if you live in a damp area.

The doorplate and little button is attractive; however, it started to stick just four weeks after I installed it. it it "brass on brass". Get the WD-40 out and keep the area around the button gently lubed if you live in a damp area. In my case, the doorbell and door are under an overhanging porch.

Polished Brass is always classy

Exactly what I was looking for. A polished brass doorbell ringer to go with my new door with brass door knob and latch.

Looks great

Must recess button into wall

Beautiful Door Bell Ringer Buttons

I ordered two brass door bell ringer buttons. They look beautiful and are heavy brass. I have not installed yet. I’m hoping they keep their polished look because they go perfect with the Baldwin brass door handles which will not tarnish.

I had to modify this doorbell button for it to work. Looks very nice & rings bell 98% of the time

When the button is pressed a circular plate is moved inward to contact the two wires thereby completing the circuit and ringing the doorbell. My button; when completely "pushed in" didn't reach the two wire contacts. The solution was to file down the brass cylinder on the back of the doorbell button (the cylinder that the plastic cylinder screws into) After the brass cylinder height was decreased about 3-4 millimeters the button's circular plate could reach the two wires contacts and complete the circuit and ring the doorbell.The screws are of very low quality metal with burs. (you might opt to replace them) The main face plate is definitely solid brass and does look very nice. However, this doorbell button "in total" is not produced with precision. The inherent variations allow a high defect rate. So install it to see if yours is good or not. And return it promptly if you are not handy enough fix the defect or have a more confounding problem. I procrastinated installing mine (missed the return window) and had to fix it to use it.I very much like the way it looks but I don't like the way it works. Infrequently the spring in the button hangs on something and the bell is not rung despite my modification. If you just press the button with a little more force the spring hang is overcome, the bell is rung and normal function returns. All in all, I have doubts about the functional longevity of this doorbell button. But ring or not, it will still look very nice.

This is the best doorbell button I've found & I've looked.

Quality product. This is my third doorbell button. Others were loose, wobbled or were poorly designed and broke almost immediately. This button is quality, solid & substantial, almost elegant and improves the look of the house.

Could be better

The doorbell itself is good quality. A little dated. The major problem is with the mounting hardware. Both mounting screws broke off and the use standard slot screws. Who uses standard slot screw anymore? I would expect phillips screws and better quality hardware

Low quality functionality. High quality look

Button has to be pushed straight in or it hangs. Great thick brass doorbell but low quality mechanisms. Have to make a bigger hole for wire if replacing a standard button.

Nice solid door bell.

Beautiful easy to install door bell. Solid brass and nice finish. I had to chip a bit of the brick/mortar (about the size of a quarter) to accommodate the back piece where the wires connect, because it protrudes from the casing, but I easily did it with a small chisel and a hammer. The end result was great, i highly recommended it.

Trick or treat I like it.

It was a treat to get this fine polished button. only 4 style points with a stiff spring push; so stiff that meek trick or treaters were reluctant to push it hard enough to make it ring. More than 90% of the holloween crowd relied on one knocker not the bell. because old neighborhoods dont always work.

Quality Doorbell Button

I wanted a doorbell button that looked good and was well made. This one is very attractive and it looks like it will last many years. It was easy to install with two supplied screws and the back wiring connection was very substantial..

A perfect little doorbell that works perfectly

This replaced an old doorbell that was hard to get to work and I'm so happy with the look and the operation of it. Glad I bought it.

Brass Doorbell Push Button

Nice and heavy true brass doorbell button. The kind that you want to install at your door. Simple low voltage 2-wire hook-up. I may just install another door bell just for my garage side entrance Would buy from Renovators Supply again.

Nice appearance/curb appeal.

Well constructed, high quality and attractive. Cannot think of any negatives.

Nice

Good quality

by now, NOTHING to know

Sorry, by now, this perfect ITEM is waiting for it's friend--my front door, and I will enjoy to find it's other friends: such as brass bell, wireless kit, etc. maybe, this will be a longway to go, maybe quickly, either, Thank U :-)

Packaging could be better...

Beautiful door bell. Shipping packaging could have been a bit better.. when i recieved it there were 2 tiny marks in the brass face plate. ....not enough to send back but ........ looks great mounted and on the wall. Thank you.

Festoon Your Porch With Class

This piece of hardware is impressive. Clean, classical look. Great quality.

High quality cast brass, polished.

Beautiful high quality - solid cast polished brass doorbell - with quality wire attachment screw fittings. Only wish the screws were oval head vs. flat slotted. Had to chisel out some stucco to make it fit. Very pleased - looks great and works well.

Five Stars

Great. I lithe it, easy to instal and looks good.

Amazing door hardware

Best looking door handle and super steady. They are heavy and feel like they would last the rest of time. Strongly recommend!

Solid, heavy piece, Good looking, sharp..

Absolutely fantastic product... Really nice... when i got the package, even before opening it, i knew it would be great... because of the weight... Its a solid plate.. the button is cool two... although I had to open the hole on my wall a bit larger to fit the back end of the button... no biggie though... Buy this item.. Its nice.

Five Stars

easy to install,works fine

The door bell is a high quality, heavy brass ...

The door bell is a high quality, heavy brass piece- substantial size, not small.<br>"I appreciate the quick response to an issue I had. Would definitely purchase from this seller again. "

Four Stars

Very nice match up with the new entry Lockset we recently installed on our newly painted door!